Danby DDR020BJWDB Dehumidifier Manual

The Danby DDR020BJWDB is a 20-pint capacity dehumidifier designed for residential use in spaces up to 500 sq. ft. It features an automatic shut-off, continuous drainage option, digital humidity readout, 24-hour timer, washable filter, and energy-efficient operation. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Operating Instructions 7. Maintenance & Cleaning 8. Storage Instructions 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Digital control panel, Water tank with full indicator, Continuous drain hose port, Washable air filter, Casters for mobility.

Feature	Description
Capacity	Removes up to 20 pints of moisture per day (at 80°F, 60% RH)
Digital Controls	Electronic touchpad with humidity display and settings
Automatic Shut-Off	Turns off when tank is full; indicator light illuminates
Continuous Drainage	Option to connect hose for automatic water removal
24-Hour Timer	Program start/stop times for energy savings
Washable Filter	Removable and reusable air filter
Humidity Control	Adjustable from 35% to 85% relative humidity
Mobility	Four swivel casters for easy room-to-room movement
Auto Restart	Resumes previous settings after power interruption
Power Cord Storage	Built-in compartment for cord management

Installation

Unpack and inspect contents. Place on level, stable surface.

Positioning: Place unit at least 6-12 inches from walls and furniture for proper airflow.
Check filter: Ensure washable filter is properly installed before operation.
Continuous drainage (optional): Attach 5/8" ID hose to drain port and route to floor drain.
Plug into dedicated 115V AC power outlet.

WARNING! Do not use extension cords. Ensure unit is upright for at least 24 hours if transported on its side.

First-Time Setup

Plug in unit; control panel will illuminate.

Set humidity level: Press HUMIDITY button to select desired level (40-50% recommended).
Select fan speed: Choose HIGH or LOW setting for dehumidification speed.
Set timer (optional): Use TIMER button to program operation schedule.
For continuous drainage: Ensure hose is securely connected and water can flow freely.

CAUTION! Operate only within 41°F to 95°F temperature range. Do not block air intake or exhaust.

Specifications

Model: DDR020BJWDB
Capacity: 20 pints per day (at 80°F, 60% RH)
Coverage Area: Up to 500 square feet
Power Supply: 115V, 60Hz, 2.5A
Water Tank Capacity: 1.2 gallons (4.5 liters)
Operating Conditions: 41°F to 95°F, up to 95% RH
Noise Level: ≤ 51 dB
Dimensions (HxWxD): 15.4" x 11.4" x 19.7"
Weight: 30.9 lbs
Refrigerant: R-410A

Controls and Settings

Control Panel: POWER, HUMIDITY SET, FAN SPEED (HIGH/LOW), TIMER, FILTER RESET.

Display Indicators: Current humidity, Set humidity, Tank full, Filter clean, Timer active.

Humidity Control: Adjust between 35-85% RH in 5% increments. Fan Speed: HIGH for maximum moisture removal, LOW for quiet operation. Timer: Program 1-24 hours for automatic start/stop. Filter Alert: FILTER light illuminates when cleaning is required (approximately every 250 hours).

Operating Instructions

For normal operation with water tank.

Press POWER to turn unit on.
Set desired humidity level using HUMIDITY buttons.
Select fan speed (HIGH or LOW).
Unit runs until set humidity is reached or tank is full.
When TANK FULL light illuminates, power off, remove tank, empty, and replace.
Unit automatically resumes operation when tank is replaced.

Tip: For maximum efficiency, keep doors and windows closed during operation.

Maintenance & Cleaning

Unplug unit before any maintenance.

Clean air filter: Remove every 2 weeks, wash with warm water and mild detergent, dry completely before reinstalling.
Reset filter indicator: Press and hold FILTER button for 3 seconds after cleaning.
Clean water tank: Empty and wash monthly with mild detergent; rinse thoroughly.
Clean exterior: Wipe with soft, damp cloth; do not use abrasive cleaners.
Check drain hose: Ensure continuous drain hose is clear of obstructions.

WARNING! Never operate without filter. Do not immerse unit in water.

Storage Instructions

When not in use for extended periods:

Unplug unit and empty water tank completely.
Clean filter and tank as described above.
Wrap power cord and store in compartment.
Store upright in cool, dry location.
Cover unit to prevent dust accumulation.

CAUTION! Allow unit to dry completely before storage to prevent mold/mildew.

Regulatory Information

UL Listed. FCC Part 15: Class B digital device; complies with interference limits for residential use. This product contains refrigerant R-410A. For proper disposal, contact local waste management authorities. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit does not start	No power/tank full	Check power outlet; ensure tank is empty and properly seated.
Low moisture removal	Room temperature/filter	Ensure room temp is 41-95°F; clean air filter; check for air blockage.
Water leakage	Tank/drain hose	Ensure tank is properly positioned; check drain hose connection.
Loud noise/vibration	Uneven surface	Place on level floor; check for loose parts.
Frost on coils	Low temperature	Turn unit off; allow frost to melt; restart when room temp >65°F.
Filter light on	Dirty filter	Clean filter as instructed; reset filter indicator.

Reset: Unplug for 5 minutes, then restart.

Service: 1-800-263-2629; www.danby.com