Danby DDR040BJ2WDB Dehumidifier Manual

The Danby DDR040BJ2WDB is a 40-pint dehumidifier designed for residential use, featuring automatic humidity control, a continuous drain option, a built-in humidistat, a 24-hour timer, auto-restart after power interruption, washable air filter, and a full tank alert with auto-shutoff. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Drainage 7. Operating Modes 8. Maintenance Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Dehumidifier unit, Water collection bucket, Washable air filter, Power cord, Drain hose adapter, User manual.

Feature	Description
Humidity Control	Built-in humidistat with adjustable settings (35%-85% RH)
Water Removal Capacity	40 pints per day (at 80°F, 60% RH)
Continuous Drain Option	Garden hose connection for unattended operation
Timer Function	24-hour programmable on/off timer
Auto-Restart	Resumes previous settings after power interruption
Full Tank Alert	Audible alarm and auto-shutoff when bucket is full
Air Filter	Washable filter for improved air quality
Control Panel	Digital display with touch controls
Power Cord	6-foot cord with storage wrap
Wheels & Handles	Portable design for easy room-to-room movement

Installation

Unpack and inspect contents. Place on level, stable surface.

Remove packaging materials and tape from unit.
Position dehumidifier: Ensure at least 12 inches clearance on all sides for proper airflow.
Install air filter: Slide washable filter into front grille until it clicks into place.
Check power requirements: Use dedicated 115V, 60Hz outlet; avoid extension cords.

WARNING! Do not place near heat sources or in direct sunlight. Ensure room temperature is between 41°F and 95°F for optimal operation.

First-Time Setup

Plug into power outlet; follow initial setup procedure.

Set humidity level: Press HUMIDITY button to select desired setting (recommended 45-50% for comfort).
Select operating mode: Choose between CONTINUOUS, AUTO, or TIMER mode.
Set timer (if needed): Press TIMER button to program on/off cycles.
Test operation: Allow unit to run for 15 minutes to ensure proper cooling and condensation.

CAUTION! Handle water bucket carefully when full; empty before moving unit.

Specifications

Model: DDR040BJ2WDB
Capacity: 40 pints per day (AHAM verified)
Operating Conditions: 41°F to 95°F, up to 90% RH
Power Supply: 115V, 60Hz, 4.5A
Water Tank Capacity: 1.6 gallons (6 liters)
Noise Level: ≤ 52 dB
Dimensions: 15.4" W × 11.4" D × 24.3" H
Weight: 40.8 lbs
Refrigerant: R410A
Warranty: 1-year parts and labor

Controls and Settings

Control Panel: POWER, MODE, HUMIDITY, FAN SPEED, TIMER, FILTER RESET.

Display Indicators: Current humidity, Set humidity, Timer status, Filter alert, Full tank alert.

Modes: CONTINUOUS (runs constantly), AUTO (maintains set humidity), TIMER (programmed operation). Fan Speeds: HIGH (maximum dehumidification), LOW (quiet operation). Humidity Settings: Adjustable from 35% to 85% in 5% increments. Timer: Program from 1 to 24 hours for automatic start/stop.

Connecting Drainage

Continuous Drain Option: Use 5/8" inner diameter garden hose (not included).

Turn off and unplug unit.
Remove water bucket from unit.
Connect hose to drain outlet at back of unit; ensure secure fit.
Route hose to floor drain, sink, or sump pump (ensure downward slope).
Replace bucket; unit will now drain continuously.

Tip: For basement use, consider installing a condensate pump if gravity drainage isn't possible.

Operating Modes

Three primary operating modes for different needs.

AUTO Mode: Unit cycles on/off automatically to maintain set humidity level.
CONTINUOUS Mode: Runs continuously regardless of humidity; use for rapid moisture removal.
TIMER Mode: Set specific operating hours; press TIMER to set start/stop times.
Fan Speed Control: HIGH for maximum air flow, LOW for quiet nighttime operation.
Auto-Defrost: Automatically activates when coil temperature drops below 41°F.

WARNING! Do not operate below 41°F; frost may form on coils and reduce efficiency.

Maintenance Features

Filter Alert: LED illuminates when filter needs cleaning (approximately every 250 hours). Full Tank Alert: Audible beep and auto-shutoff when bucket is full. Auto-Restart: After power outage, resumes previous settings automatically.

Care & Cleaning

Unplug before cleaning. Clean exterior with damp cloth; mild detergent if needed.

Air Filter: Remove monthly, wash with warm soapy water, dry completely before reinstalling.
Water Bucket: Empty regularly, clean with mild detergent to prevent mold/mildew.
Coils and Grilles: Vacuum gently every 3 months to remove dust.
End-of-Season: Empty bucket, clean filter, dry interior, cover unit for storage.

CAUTION! Never use abrasive cleaners or immerse unit in water. Do not operate without filter installed.

Regulatory Information

UL Listed: Meets UL standard 474. Energy Star: Certified for energy efficiency. EPA Refrigerant: Uses R410A, an environmentally friendly refrigerant. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not starting	Power issue/full bucket	Check power outlet; ensure bucket is properly seated and empty.
Low moisture removal	Room conditions/filter	Ensure room temp 41°F-95°F; clean air filter; check for closed doors/windows.
Water leaking	Improper hose connection	Check hose connection; ensure bucket is properly positioned.
Loud noise	Uneven surface/fan obstruction	Place on level surface; check for objects near fan.
Ice on coils	Low temperature	Move to warmer area; auto-defrost should activate within 30 minutes.
Filter light on	Dirty filter	Clean air filter; press and hold FILTER button for 3 seconds to reset.

Reset: Unplug for 5 minutes to reset electronic controls.

Service: 1-800-263-2629; www.danby.com