Danby DDR050BHWDB Dehumidifier Manual

The Danby DDR050BHWDB is a 50-pint capacity dehumidifier designed for residential use, featuring automatic humidity control, continuous drain option, washable air filter, auto-defrost, digital controls with LED display, 24-hour timer, full bucket alert with auto shut-off, and energy-efficient operation. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Drain Hose 7. Operation Modes 8. Maintenance 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Digital control panel, Removable water bucket, Washable air filter, Continuous drain port, Casters for mobility, Handle for transport.

Feature	Description
Digital Control Panel	LED display with humidity readout and settings
Automatic Humidity Control	Set desired humidity level (35%-85%)
Continuous Drain Option	Garden hose connection for unattended operation
Washable Air Filter	Removable filter for easy cleaning
Auto-Defrost Function	Prevents coil freezing in low temperatures
24-Hour Timer	Program start/stop times
Full Bucket Alert	LED indicator and auto shut-off when bucket is full
Energy Efficient	Energy Star certified operation
Casters and Handle	Easy mobility between rooms
Power Cord Storage	Convenient cord wrap on back of unit

Installation

Unpack and inspect contents. Place on level surface.

Remove packaging materials and tape from unit.
Place dehumidifier on firm, level floor at least 6 inches from walls.
Ensure proper air circulation: Keep vents unobstructed.
Check power requirements: 115V, 60Hz grounded outlet.
Install air filter: Ensure filter is properly seated in front grille.

WARNING! Do not use extension cords. Ensure proper grounding. Do not place near heat sources.

First-Time Setup

Plug in unit; follow initial setup procedure.

Initial power on: Plug into grounded outlet, unit will beep and display current humidity.
Set desired humidity: Press HUMIDITY button to set target (recommended 45-50%).
Select fan speed: Choose HIGH or LOW fan setting.
Set timer (optional): Program 24-hour timer for automatic operation.
Test bucket removal: Practice removing and replacing water bucket.

CAUTION! Allow unit to stand upright for 24 hours if transported on its side.

Specifications

Capacity: 50 pints per day (at 80°F, 60% RH).
Coverage Area: Up to 1500 sq. ft.
Operating Temperature: 41°F to 95°F.
Humidity Control Range: 35% to 85% relative humidity.
Water Bucket Capacity: 1.6 gallons.
Fan Speeds: 2 speeds (High/Low).
Power Requirements: 115V, 60Hz, 4.5A.
Dimensions: 15.4" W × 11.4" D × 24.3" H.
Weight: 41.9 lbs.
Refrigerant: R410A.

Controls and Settings

Digital control panel located on top of unit.

Control Buttons: POWER, HUMIDITY SET, FAN SPEED, TIMER, MODE.

Display Indicators: Current humidity, Set humidity, Fan speed, Timer, Full bucket, Defrost, Continuous drain mode.

Settings: Humidity level (35%-85%), Fan speed (HIGH/LOW), Mode (Normal/Continuous/Turbo), Timer (1-24 hours), Filter reset indicator.

Connecting Drain Hose

For continuous operation without bucket emptying.

Turn off and unplug unit.
Remove water bucket from unit.
Locate drain port on back of unit.
Insert garden hose (¾" diameter) into drain port.
Route hose to floor drain, sink, or sump pump.
Replace bucket (unit will not operate without bucket in place).
Select CONTINUOUS mode on control panel.

Tip: Ensure hose has downward slope for proper drainage.

Operation Modes

Three operating modes available.

Normal Mode: Unit runs until set humidity is reached, then cycles on/off automatically.
Continuous Mode: Unit runs continuously regardless of humidity level (use with drain hose).
Turbo Mode: Maximum moisture removal with high fan speed.
Auto-Defrost: Automatically activates when coil temperature drops below 41°F.
Timer Operation: Set to turn unit on/off at specific times (1-24 hour programming).

WARNING! Do not operate below 41°F without auto-defrost function active.

Maintenance

Regular maintenance ensures optimal performance.

Air Filter: Clean every 2 weeks or as needed. Remove, wash with warm soapy water, dry completely, reinstall.

Water Bucket: Empty regularly, clean monthly with mild detergent.

Exterior: Wipe with damp cloth, dry thoroughly.

Coils: Vacuum annually to remove dust accumulation.

Care & Cleaning

Unplug before cleaning. Use mild detergent only; no abrasive cleaners.

CAUTION! Never immerse unit in water. Do not use chemical cleaners on coils.

Regulatory Information

UL Listed. Energy Star Certified. FCC Part 15 Compliant. This product contains refrigerant that must be recovered by certified technicians. For disposal, consult local regulations. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not starting	Power/bucket	Check power connection; ensure bucket is properly seated.
Reduced moisture removal	Filter/temperature	Clean air filter; ensure room temperature above 41°F.
Water leaking	Bucket/hose	Ensure bucket is properly inserted; check hose connections.
Loud operation	Placement/vibration	Place on level surface; check for loose parts.
Display not working	Power/reset	Unplug for 5 minutes, then restart; check circuit breaker.
Ice on coils	Low temperature	Auto-defrost should activate; move to warmer area if persistent.

Reset: Unplug for 5 minutes to reset electronic controls.

Service: 1-800-263-2629; www.danby.com