Danby DDR050BJPWDB-6 Dehumidifier Manual

The Danby DDR050BJPWDB-6 is a 50-pint dehumidifier designed for residential use, featuring automatic humidity control, continuous drainage capability, a 24-hour timer, washable air filter, auto-restart function, and low-temperature operation. Ideal for medium to large rooms up to 3000 sq. ft. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Control panel with digital display, Water tank with full indicator, Continuous drain hose connection, Washable air filter, Casters for mobility, Carrying handle.

Installation & Placement

Unpack and inspect contents. Place on level, stable surface.

1. Remove all packaging materials and tape from unit.
2. Position dehumidifier at least 12 inches from walls and furniture for proper airflow.
3. Ensure the unit is placed on a level surface to prevent water leakage.
4. Keep away from heat sources and direct sunlight.
5. Install casters by pressing into bottom corners until they click into place.

WARNING! Do not operate in standing water. Ensure proper ventilation around the unit.

First-Time Setup

Plug into grounded 115V outlet; follow initial setup procedure.

1. Insert water tank securely until it clicks into place.
2. Plug power cord into dedicated 115V, 60Hz grounded outlet.
3. Press POWER button to turn on unit.
4. Set desired humidity level using UP/DOWN buttons (recommended 45-50% RH).
5. Select operating mode: Normal, Turbo, or Sleep.
6. For continuous drainage: Connect garden hose to drain port (see section 8).

CAUTION! Do not use extension cords. Ensure hands are dry when operating controls.

Specifications

• Model: DDR050BJPWDB-6
• Capacity: 50 pints per day (at 60% RH, 80°F)
• Coverage Area: Up to 3000 square feet
• Water Tank: 50-pint removable bucket with handle
• Power Requirements: 115V, 60Hz, 5.5A
• Operating Temperature: 41°F to 95°F (5°C to 35°C)
• Noise Level: 52 dB on normal mode
• Dimensions: 15.4" W × 11.4" D × 24.3" H
• Weight: 41.9 lbs
• Refrigerant: R410a

Controls and Settings

Control Panel: POWER, MODE, TIMER, UP/DOWN buttons, FILTER indicator, TANK FULL indicator.

Display Indicators: Current humidity, Set humidity, Timer status, Filter alert, Tank full, Mode icons.

Humidity Setting: Adjust between 30% and 90% RH in 5% increments. Modes: Normal (standard operation), Turbo (maximum dehumidification), Sleep (quiet operation with dimmed display). Timer: Programmable 1-24 hours for automatic on/off. Filter Reset: Hold FILTER button for 3 seconds after cleaning filter.

Operation Modes

Normal Mode: Standard dehumidification with balanced energy use. Turbo Mode: Maximum moisture removal for high humidity. Sleep Mode: Reduced noise and dimmed display for nighttime.

1. Press POWER to turn unit on.
2. Press MODE to cycle through Normal, Turbo, and Sleep modes.
3. Use UP/DOWN buttons to set desired humidity level.
4. Press TIMER to set automatic shut-off (1-24 hours).
5. Unit will automatically cycle to maintain set humidity level.

Tip: For energy savings, set humidity to 50% when occupied, 60% when unoccupied.

Drainage Options

Two drainage methods: Manual (water tank) or Continuous (garden hose).

1. Manual Drainage: Unit stops when tank is full (indicator lights). Remove tank by pulling handle, empty, and replace.
2. Continuous Drainage: Connect standard garden hose (¾" diameter) to drain port at back of unit. Route hose to floor drain or suitable outlet. Ensure hose runs downward without kinks.
3. Gravity Drainage: For continuous operation, place unit higher than drain point (minimum 12-inch elevation).

WARNING! Do not drink collected water. Empty tank regularly to prevent overflow.

Maintenance & Cleaning

Unplug unit before any maintenance. Monthly cleaning recommended.

1. Air Filter: Remove filter monthly, wash with warm water and mild detergent, air dry completely before reinstalling.
2. Water Tank: Clean monthly with mild detergent, rinse thoroughly.
3. Exterior: Wipe with damp cloth, then dry. Do not use abrasive cleaners.
4. Coils: Vacuum condenser coils every 3 months to maintain efficiency.
5. End of Season: Empty tank completely, clean unit, and store properly.

CAUTION! Never immerse unit in water. Do not use chemical cleaners on filter.

Care & Storage

For seasonal storage or extended non-use:

1. Unplug unit and empty water tank completely.
2. Clean filter, tank, and exterior as described above.
3. Wrap power cord neatly around cord hooks.
4. Store in upright position in dry, covered area.
5. Cover unit to prevent dust accumulation.

Important: Store at temperatures between 41°F and 95°F. Do not store with water in tank.

Regulatory Information

UL Listed: Meets UL standard 474. Energy Star: Certified for energy efficiency. FCC Part 15: Class B digital device compliant. Refrigerant: Contains R410a. For recycling information, contact local waste management. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Reset: Unplug for 5 minutes to reset electronic controls.

Service: 1-800-263-2629; www.danby.com