Danby DDR050BJPWDB Dehumidifier Manual

The Danby DDR050BJPWDB is a 50-pint dehumidifier designed for residential use, featuring automatic humidity control, continuous drainage option, washable air filter, auto-restart after power interruption, 24-hour timer, and energy-efficient operation. Suitable for areas up to 3000 sq. ft. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Drainage 7. Operating Modes 8. Maintenance 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control panel with digital display, Water tank with full indicator, Continuous drain port, Washable air filter, Casters for mobility, Power cord.

Feature	Description
Humidity Control	Automatic humidity sensing and adjustment
Digital Display	Shows current humidity, timer, and settings
Continuous Drain	Option for hose connection (not included)
Water Tank	Removable 50-pint capacity with full indicator
Air Filter	Washable filter for improved air quality
Timer	24-hour programmable on/off timer
Auto-Restart	Resumes previous settings after power outage
Turbo Mode	High-speed dehumidification
Energy Efficient	Energy Star certified
Mobility	Four casters for easy movement

Installation

Unpack and inspect contents. Place on level surface.

Remove packaging: Remove all tape and protective materials.
Position unit: Place on flat, stable surface at least 12 inches from walls.
Check airflow: Ensure air intake and exhaust are unobstructed.
Allow upright time: Let unit stand upright for 24 hours before first use if transported horizontally.
Plug into grounded outlet: Use dedicated 115V AC, 60Hz outlet.

WARNING! Do not use extension cords. Ensure proper ventilation around unit.

First-Time Setup

Power on dehumidifier; follow initial setup steps.

Set humidity level: Press HUMIDITY button to set desired level (35%-85%).
Select mode: Choose AUTO (recommended) or TURBO for faster dehumidification.
Set timer: Press TIMER to program on/off schedule if needed.
Check filter: Ensure air filter is clean and properly installed.
Monitor operation: Verify water collection begins within first hour.

CAUTION! Do not operate in temperatures below 41°F (5°C).

Specifications

Model: DDR050BJPWDB
Capacity: 50 pints per day (at 60°F, 60% RH)
Coverage: Up to 3000 sq. ft.
Power: 115V AC, 60Hz, 4.5A
Water Tank: 50-pint removable bucket
Dimensions: 15.4" W × 11.4" D × 24.3" H
Weight: 40.8 lbs
Operating Temp: 41°F to 95°F (5°C to 35°C)
Refrigerant: R410A
Certifications: Energy Star, ETL listed

Controls and Settings

Control Panel: POWER, MODE, HUMIDITY, TIMER, FILTER RESET.

Display Indicators: Current humidity, Set humidity, Timer, Filter alert, Full tank, Turbo mode.

Humidity Control: Set between 35%-85% in 5% increments. Modes: AUTO (maintains set humidity), TURBO (maximum dehumidification), CONTINUOUS (runs continuously). Timer: Program on/off times in 1-hour increments up to 24 hours. Filter Reset: Press after cleaning filter to reset alert.

Connecting Drainage

Continuous drain option for unattended operation.

Turn off and unplug unit.
Remove drain cap from back of unit.
Connect 5/8" ID hose (not included) to drain port.
Route hose to floor drain or suitable drainage area.
Ensure hose has downward slope without kinks.
Replace water tank to activate continuous drainage.

Tip: For gravity drainage, place unit higher than drain point.

Operating Modes

Three operating modes for different needs.

AUTO Mode: Unit cycles on/off to maintain set humidity level.
TURBO Mode: Runs continuously at maximum speed until turned off.
CONTINUOUS Mode: Runs continuously regardless of humidity level.
Timer Operation: Set unit to turn on/off at specific times.
Auto-Defrost: Automatically activates in low temperatures to prevent frost buildup.

WARNING! Do not operate in enclosed spaces without ventilation.

Maintenance

Regular maintenance ensures optimal performance.

Daily: Check and empty water tank when full indicator lights.
Weekly: Check air filter; clean if dirty.
Monthly: Clean exterior with damp cloth.
Seasonally: Deep clean air filter and check drain hose.
Annually: Professional inspection recommended.

Care & Cleaning

Unplug before cleaning. Clean exterior with soft, damp cloth. Do not use abrasive cleaners.

Air Filter Cleaning:

Remove filter from front grille.
Vacuum loose dust or rinse under lukewarm water.
Allow to dry completely before reinstalling.
Press FILTER RESET button on control panel.

CAUTION! Never immerse unit in water. Do not use chemical cleaners on filter.

Regulatory Information

ETL listed to UL standard 474. Energy Star certified. This product contains R410A refrigerant. For proper disposal, consult local regulations. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not starting	Power issue	Check power cord connection; ensure outlet works; check circuit breaker.
Poor dehumidification	Temperature/RH	Ensure room temp above 41°F; check humidity setting; clean filter.
Water not collecting	Drain setup	Check continuous drain connection; ensure tank is properly seated.
Unit freezing up	Low temperature	Move to warmer area; auto-defrost should activate within 30 minutes.
Loud noise	Vibration/obstruction	Ensure unit is level; check for objects touching unit; clean filter.
Error codes on display	System fault	Unplug for 10 minutes, then restart; if persists, contact service.

Reset: Unplug for 10 minutes to reset control system.

Service: 1-800-263-2629; www.danby.com