Danby DDR050BJPWDB-RF Dehumidifier Manual

The Danby DDR050BJPWDB-RF is a 50-pint dehumidifier designed for residential use, featuring automatic humidity control, a continuous drain option, a full-bucket alert with auto-shutoff, a washable air filter, and a digital display with touch controls. It operates on 115V/60Hz power and is ideal for medium to large rooms. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Operation Modes 7. Maintenance 8. Care & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Digital control panel, removable water bucket, continuous drain hose connection, washable air filter, and caster wheels for mobility.

Feature	Description
Digital Display	Shows current humidity, settings, and alerts
Automatic Humidity Control	Maintains set humidity level (30%-80% RH)
Continuous Drain Option	Allows connection to a hose for unattended operation
Full-Bucket Alert & Auto-Shutoff	Stops operation and lights indicator when bucket is full
Washable Air Filter	Captures dust and particles; can be cleaned
24-Hour Timer	Programs unit to turn on/off at set times
Turbo Mode	Increases fan speed for faster dehumidification
Defrost Function	Automatically activates in low temperatures
Caster Wheels	For easy mobility between rooms
Power Cord Storage	Built-in compartment for neat storage

Installation

Unpack and inspect contents. Place on a level, stable surface.

Positioning: Ensure at least 12 inches of clearance on all sides for proper airflow.
Bucket Installation: Slide the empty water bucket into place until it clicks.
Continuous Drain Setup (Optional): Remove bucket, attach drain hose to outlet, and route hose to floor drain or suitable container.
Power Connection: Plug into a dedicated 115V outlet. Do not use an extension cord.

WARNING! Do not operate in temperatures below 41°F (5°C). Ensure the unit is upright for at least 24 hours before first use if transported on its side.

First-Time Setup

Power on the dehumidifier; the digital display will illuminate.

Set Desired Humidity: Press the HUMIDITY button to cycle between 30%, 40%, 50%, 60%, 70%, or 80% relative humidity (Auto mode recommended).
Select Fan Speed: Press FAN button for Low (quiet) or High (Turbo) speed.
Set Timer (Optional): Press TIMER to program automatic start/stop up to 24 hours.
Check Filter: Ensure the air filter is clean and properly seated.

CAUTION! Do not block air intake or exhaust grilles. Place away from curtains and furniture.

Specifications

Model: DDR050BJPWDB-RF
Dehumidification Capacity: 50 pints per day (at 80°F, 60% RH)
Operating Voltage/Frequency: 115V, 60Hz
Power Consumption: 4.5 Amps
Operating Temperature Range: 41°F to 95°F (5°C to 35°C)
Water Bucket Capacity: 1.6 gallons (6 liters)
Air Flow: 165 CFM (High speed)
Noise Level: ≤ 52 dB(A)
Refrigerant: R410A
Dimensions (HxWxD): 23.4" x 15.0" x 11.2"
Weight: 40.8 lbs

Controls and Settings

Access all functions via the digital control panel or included remote control.

Control Panel: POWER, HUMIDITY, FAN (Low/High/Turbo), TIMER, MODE (Continuous/Auto), FILTER ALERT RESET.

Display Icons: Power, Bucket Full, Defrost, Filter Clean, Humidity Setpoint, Fan Speed, Timer.

Humidity Control: Set target from 30% to 80% RH. In Auto mode, unit cycles to maintain set point. Fan Speed: Low for quiet operation, High for normal, Turbo for maximum moisture removal. Timer: Set 1-24 hours for delayed start or auto shut-off. Continuous Mode: Runs constantly until turned off or bucket is full. Defrost: Automatically activates when coil temperature is low; compressor pauses, fan may run.

Operation Modes

Auto (Default): Maintains set humidity level by cycling compressor and fan. Continuous: Runs compressor continuously for maximum dehumidification. Turbo: Fan runs at highest speed for rapid moisture removal.

For normal use, select Auto mode and set desired humidity (45%-55% recommended).
For very damp conditions (e.g., after flooding), use Continuous or Turbo mode initially.
In colder environments (below 65°F), the defrost cycle may activate more frequently.

Tip: Close windows and doors in the room for best efficiency.

Maintenance

Regular maintenance ensures optimal performance and longevity.

Empty Water Bucket: When full, unit will shut off and indicator will light. Remove bucket, pour out water, and reinsert securely.
Clean Air Filter Every 2 Weeks: Remove filter, rinse with lukewarm water, let dry completely, and reinstall. Press FILTER RESET button.
Clean Exterior: Wipe cabinet with a soft, damp cloth. Do not use harsh chemicals.
End-of-Season Storage: Empty and dry bucket. Clean filter. Coil drain hose if used. Store upright in a dry place.

WARNING! Always unplug the unit before performing any maintenance. Do not operate without the air filter installed.

Care & Cleaning

Unplug before cleaning. Use only a soft, damp cloth for the exterior. Clean the air filter regularly.

CAUTION! Do not immerse unit in water. Do not use gasoline, thinners, or abrasive cleaners.

Regulatory Information

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. This product contains refrigerant R410A. For proper disposal, consult local regulations. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit does not start	No power, bucket full, timer set	Ensure plugged in; empty bucket; check timer settings.
Little or no water collection	Low humidity, low temperature, dirty filter	Check room humidity; ensure temp >41°F; clean air filter.
Unit runs but stops frequently	Defrost cycle active, set humidity reached	Normal in low temps; if in Auto mode, unit cycles to maintain set point.
Loud or unusual noise	Uneven surface, loose parts, fan obstruction	Place on level floor; ensure cabinet panels are secure; check for debris near fan.
Bucket full light on but bucket not full	Bucket not seated properly, float mechanism stuck	Remove and reinsert bucket; check float moves freely.
Error code "E1" or "E2" on display	Sensor fault	Unplug for 5 minutes, then restart. If persists, contact service.

Reset: Unplug unit for 5 minutes to reset control system.

Service: 1-800-263-2629; www.danby.com