Danby DDR050BJWDB-ME Dehumidifier Manual

The Danby DDR050BJWDB-ME is a 50-pint dehumidifier designed for medium to large rooms, featuring an electronic control panel with digital display, auto-restart, continuous drain option, washable filter, 24-hour timer, and humidity control settings. It operates on 115V, 60Hz, and includes features like auto-defrost, full bucket alert, and caster wheels for mobility. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Continuous Drain Option 7. Maintenance & Cleaning 8. Storage Instructions 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Electronic control panel, Digital humidity display, Water collection bucket, Washable air filter, Continuous drain hose connection, Caster wheels, Auto-defrost function.

Feature	Description
Electronic Control Panel	Digital interface for setting humidity level, timer, and mode
50-Pint Capacity	Removes up to 50 pints of moisture per day (at 80°F, 60% RH)
Continuous Drain Option	Allows connection of a hose for automatic water removal
Washable Air Filter	Captures dust and particles; can be cleaned and reused
Auto-Defrost	Prevents frost buildup in low-temperature conditions
24-Hour Timer	Program start/stop times for energy efficiency
Full Bucket Alert	Indicator light and auto-shutoff when bucket is full
Caster Wheels	Provides easy mobility between rooms
Auto-Restart	Resumes previous settings after a power interruption
Humidity Control	Adjustable from 35% to 85% relative humidity

Installation & Setup

Unpack and inspect contents. Place on a level, stable surface.

Positioning: Place the dehumidifier at least 6 inches away from walls and furniture for proper airflow.
Install Casters: Attach the four caster wheels to the base if not pre-installed.
Check Filter: Ensure the washable air filter is properly seated in its slot.
Power Connection: Plug the power cord into a grounded 115V, 60Hz outlet.
Bucket Placement: Ensure the water collection bucket is correctly inserted and locked into place.

WARNING! Do not use an extension cord. Ensure the unit is upright for at least 24 hours before first use if it was laid on its side during transport.

First-Time Operation

Power on the dehumidifier; the digital display will illuminate.

Set Desired Humidity: Press the HUMIDITY button to set your target level (35%-85%).
Select Mode: Choose between CONTINUOUS (runs constantly) or AUTO (cycles based on humidity setting).
Set Timer (Optional): Use the TIMER button to program automatic start/stop times.
Monitor Operation: The display shows current room humidity and bucket status.
Empty Bucket: When the FULL bucket indicator lights, power off, remove, and empty the bucket.

CAUTION! Always turn off and unplug the unit before removing the water bucket.

Specifications

Model: DDR050BJWDB-ME
Dehumidification Capacity: 50 pints per day (at 80°F, 60% RH)
Power Supply: 115V AC, 60Hz
Amperage: 5.0A
Water Bucket Capacity: 1.6 gallons (6 liters)
Operating Temperature Range: 41°F to 95°F (5°C to 35°C)
Air Flow: 165 CFM (Cubic Feet per Minute)
Noise Level: ≤ 52 dB
Dimensions (HxWxD): 23.4" x 15.4" x 11.8"
Weight: 41.9 lbs
Refrigerant: R-410A

Controls and Settings

Access all functions via the electronic control panel on the top of the unit.

Control Panel Buttons & Display: POWER, MODE (Continuous/Auto), HUMIDITY (+/-), TIMER (Up/Down), FILTER RESET.

Display Icons: Current Humidity %, Target Setting, Bucket Full, Filter Clean, Timer, Defrost.

Humidity Setting: Adjust in 5% increments from 35% to 85%. Timer: Programmable in 1-hour increments up to 24 hours. Filter Reset: Press and hold for 3 seconds after cleaning the filter to reset the reminder light. Auto-Defrost: Activates automatically when coil temperature drops below 41°F (5°C).

Continuous Drain Option

For automatic water drainage, use the provided drain hose adapter.

Locate the drain outlet on the back of the unit.
Remove the rubber plug from the outlet.
Attach a standard 5/8" inner diameter garden hose (not included) to the outlet.
Route the hose to a floor drain, sink, or sump pump. Ensure the hose runs downhill without kinks.
When using continuous drain, the bucket does not need to be in place. The bucket full alert will be disabled.

Tip: For best performance, the drain hose should be no longer than 10 feet.

Maintenance & Cleaning

Unplug the unit before any maintenance.

Cleaning the Air Filter: Remove the filter every 2 weeks or as needed. Rinse under lukewarm water and let air dry completely before reinstalling. Press the FILTER RESET button.
Cleaning the Exterior: Wipe the cabinet with a soft, damp cloth. Do not use abrasive cleaners or solvents.
Cleaning the Water Bucket: Empty and wash the bucket with mild detergent monthly to prevent mold/mildew. Rinse thoroughly.
End-of-Season Cleaning: Run the unit in FAN mode for a few hours to dry internal components before storage.

CAUTION! Never immerse the unit in water. Do not operate without the air filter installed.

Storage Instructions

If not using the dehumidifier for an extended period:

Unplug the unit from the electrical outlet.
Empty and thoroughly clean the water bucket. Let it air dry.
Clean the air filter and let it dry.
Coil the power cord neatly and secure it.
Store the unit upright in a cool, dry place. Cover it to prevent dust accumulation.

WARNING! Do not store the unit on its side or in a location where it may be exposed to freezing temperatures while wet.

Regulatory Information

This appliance complies with FCC Part 15 Subpart B for unintentional radiators. Operation is subject to the condition that this device does not cause harmful interference. Copyright © Danby Products Inc. All rights reserved. For support, visit www.danby.com or contact customer service at 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit does not start	No power / Full bucket	Ensure unit is plugged in and outlet is live. Check if bucket is full and properly seated.
Reduced moisture removal	Dirty filter / Low temp	Clean the air filter. Ensure room temperature is above 41°F (5°C).
Unit runs but no water in bucket	Low humidity / Frost	Room humidity may already be at or below set point. Allow auto-defrost cycle to complete.
Unusual noise	Loose parts / Debris	Ensure unit is on a level surface. Check for foreign objects near the fan.
Error code on display (e.g., E1, E2)	Sensor fault	Unplug unit for 5 minutes, then restart. If error persists, contact service.
Water leakage	Misaligned bucket / Clogged drain	Remove and reinsert bucket. Check continuous drain hose for kinks or blockages.

Reset: Unplug the unit for 5 minutes to perform a full system reset.

Service: 1-800-263-2629; www.danby.com