Danby DDR050CBLPMBDB Dehumidifier Manual

The Danby DDR050CBLPMBDB is a 50-pint capacity dehumidifier designed for residential use. It features automatic humidity control, a continuous drain option, a built-in humidistat, a washable air filter, an auto-defrost function for low-temperature operation, a full-bucket alert with auto-shutoff, a 24-hour timer, and caster wheels for mobility. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Placement 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Operation Modes 7. Maintenance & Cleaning 8. Storage Instructions 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Control Panel, Water Bucket, Air Filter, Drain Hose Connector, Caster Wheels, Handle.

Feature	Description
Humidistat	Automatic humidity sensing and control
Continuous Drain Option	Connection for gravity-fed drain hose
Auto-Defrost	Prevents coil freezing in low temperatures
Full Bucket Alert	Indicator light and auto-shutoff when bucket is full
24-Hour Timer	Programmable on/off cycles
Washable Air Filter	Captures airborne particles; can be cleaned
Control Lock	Prevents accidental setting changes
Caster Wheels	For easy mobility
Power Cord Storage	Integrated hooks for cord management
Bucket Handle	For easy removal and transport

Installation & Placement

Unpack and inspect contents. Place on a level, stable floor.

Positioning: Place at least 6-12 inches from walls and furniture for proper airflow.
Check Bucket: Ensure water bucket is correctly seated and locked in place.
Continuous Drain Setup (Optional): Attach drain hose to connector; route to floor drain or sink.
Plug into a dedicated 120V AC outlet.

WARNING! Do not place in areas with temperatures below 41°F (5°C) or above 95°F (35°C). Ensure the unit is upright for at least 24 hours before first use if transported on its side.

First-Time Setup

Plug in the unit; the control panel will illuminate.

Set Desired Humidity: Press the HUMIDITY button to select a target level (35%-85%).
Select Fan Speed: Choose LOW or HIGH using the FAN button.
Set Timer (Optional): Use TIMER button to program automatic start/stop.
Start Operation: Press the POWER button to begin dehumidification.

CAUTION! Always use the handle to carry the water bucket. Do not operate without the air filter installed.

Specifications

Model: DDR050CBLPMBDB
Capacity: 50 pints per day (at 60% RH, 80°F)
Operating Range: 41°F to 95°F (5°C to 35°C)
Power Supply: 115V, 60Hz
Amperage: 4.5A
Water Bucket Capacity: 1.6 gallons (6 liters)
Air Flow: High/Low settings
Noise Level: ≤ 52 dB(A)
Dimensions (HxWxD): 23.6" x 15.4" x 11.8"
Weight: 36.4 lbs
Refrigerant: R-410A

Controls and Settings

Control Panel: POWER, HUMIDITY, FAN, TIMER, FILTER ALERT, FULL BUCKET indicator.

Humidity Control: Set target humidity from 35% to 85% in 5% increments. Unit cycles automatically to maintain setting.

Fan Speed: LOW for quiet operation, HIGH for maximum moisture removal.

Timer: Program ON or OFF delay from 1 to 24 hours.

Auto-Defrost: Activates automatically when frost is detected on coils.

Control Lock: Press and hold HUMIDITY and FAN for 3 seconds to lock/unlock panel.

Operation Modes

Normal Mode: Unit runs until target humidity is reached, then cycles on/off.

Continuous Mode: Set humidity to "CONT" for non-stop operation (ideal for very damp areas).

Laundry Mode: High fan speed with continuous operation to dry laundry in closed room.

Select mode via HUMIDITY button.
Monitor bucket level; empty when FULL indicator lights.
For continuous drain, ensure hose is securely attached and unobstructed.

Tip: Close windows and doors in the room for optimal efficiency.

Maintenance & Cleaning

Unplug unit before any maintenance.

Empty Water Bucket: Remove, empty, and reinsert securely.
Clean Air Filter: Remove filter every 2 weeks; rinse with warm water; dry completely before reinstalling.
Clean Exterior: Wipe with a soft, damp cloth; do not use abrasive cleaners.
End-of-Season Cleaning: Run in Fan Only mode for 24 hours to dry internal components before storage.

WARNING! Never use the unit without the air filter. Do not immerse unit in water.

Storage Instructions

If not using for an extended period:

Unplug the unit.
Empty and dry the water bucket completely.
Clean the air filter and let it dry.
Coil the power cord and secure it on the storage hooks.
Store upright in a cool, dry place.

CAUTION! Store in an area protected from dust and extreme temperatures.

Regulatory Information

This appliance complies with FCC Part 15 Subpart B. Operation is subject to the condition that it does not cause harmful interference. This product contains refrigerant R-410A. For proper disposal, consult local regulations. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit does not start	No power / Bucket full	Check outlet; ensure bucket is empty and properly seated.
Little or no water collection	Low humidity / Cold room	Room may already be dry; ensure room temp is above 41°F (5°C).
Unit runs continuously	Set to CONTINUOUS mode / High humidity	Check humidity setting; select a target % if not needed continuously.
Frost on coils	Low temperature	Auto-defrost should activate; move unit to warmer area if persistent.
Unusual noise	Loose parts / Dirty filter	Ensure unit is level; check and clean air filter.
FILTER alert lit	Dirty air filter	Clean the air filter as per instructions.

Reset: Unplug for 60 seconds, then restart.

Service: 1-800-263-2629; www.danby.com