Danby DDR070BBPBDB Dehumidifier Manual

The Danby DDR070BBPBDB is a 70-pint dehumidifier designed for residential use, featuring automatic humidity control, a continuous drain option, a built-in humidistat, a 24-hour timer, washable air filter, auto-defrost function, and a full-bucket alert with auto-shutoff. It operates on 115V, 60Hz power. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Placement 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Operation Modes 7. Maintenance & Cleaning 8. Drainage Options 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Control Panel, Air Intake Grille, Air Filter, Water Collection Bucket, Continuous Drain Hose Connection, Casters for Mobility, and Exhaust Grille.

Feature	Description
Humidistat	Automatically maintains desired humidity level (35%-85% RH)
Water Bucket	Removable 1.3-gallon bucket with full indicator and auto-shutoff
Continuous Drain	Option for hose connection (5/8" inner diameter) for unattended operation
24-Hour Timer	Programmable on/off cycles
Air Filter	Washable mesh filter to capture dust and particles
Auto Defrost	Prevents coil freezing in low temperatures
Control Lock	Prevents accidental setting changes
Power Cord Storage	Integrated hooks for cord management
Casters	Four wheels for easy mobility
Digital Display	Shows current humidity, set point, timer, and alerts

Installation & Placement

Unpack and inspect contents. Place on a level, stable floor.

Clearance: Ensure at least 12 inches of space around all sides, especially near walls and furniture.
Positioning: Place in the center of the room or area with high humidity for best performance.
Power Source: Plug directly into a grounded 115V, 60Hz outlet. Do not use an extension cord.
Bucket Installation: Insert the empty water bucket securely until it clicks into place.

WARNING! Do not operate in temperatures below 41°F (5°C). Ensure the unit is upright for at least 24 hours before first use if transported on its side.

First-Time Setup

Plug in the unit; the control panel will illuminate.

Set Humidity Level: Press the HUMIDITY button and use +/- to set desired RH (recommended 45-50%).
Select Mode: Choose between CONTINUOUS (runs constantly) or AUTO (uses humidistat).
Set Timer (Optional): Press TIMER to program automatic start/stop times.
Check Drainage: Decide to use the bucket or connect a drain hose (see section 9).

CAUTION! Handle the water bucket carefully to avoid spills. Ensure the bucket is correctly seated before operation.

Specifications

Model: DDR070BBPBDB
Capacity: 70 pints per day (at 80°F, 60% RH)
Bucket Capacity: 1.3 gallons (5 liters)
Operating Conditions: 41°F to 95°F (5°C to 35°C)
Humidity Control Range: 35% to 85% RH
Power Supply: 115V, 60Hz, 6.5A
Air Flow: 188 CFM
Noise Level: ≤ 51 dB
Dimensions (HxWxD): 23.4" x 15.4" x 11.8"
Weight: 40.8 lbs
Refrigerant: R410a

Controls and Settings

Access all functions via the digital control panel or included remote control.

Control Panel: POWER, MODE (Continuous/Auto), HUMIDITY Set, FAN Speed (High/Low), TIMER, FILTER Reset, LOCK.

Display Icons: Power, Bucket Full, Defrost, Filter Clean, Timer, Lock, Fan Speed, Target Humidity.

Settings: Humidity Set Point (35%-85%), Fan Speed (High for fast dehumidification, Low for quiet operation), Timer (1-24 hours), Auto Restart (resumes previous settings after power outage).

Operation Modes

AUTO Mode: Unit cycles on/off automatically to maintain the set humidity level. The compressor and fan run until the set point is reached, then shut off until humidity rises.

CONTINUOUS Mode: Unit runs continuously regardless of humidity level. Use for maximum moisture removal or in very damp conditions.

Timer Mode: Program the unit to turn ON or OFF after a set delay (1-24 hours). Useful for scheduled operation.

Fan Only Mode: Circulates air without dehumidifying. Press FAN button when unit is off to activate.

Maintenance & Cleaning

Unplug the unit before any maintenance.

Air Filter: Clean every 2 weeks or as needed. Remove, wash with warm water and mild detergent, dry completely, and reinstall.
Water Bucket: Empty and clean monthly with mild detergent to prevent mold/mildew. Rinse thoroughly.
Exterior: Wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents.
Grilles and Coils: Use a vacuum brush attachment to remove dust from intake and exhaust grilles annually.

CAUTION! Never immerse the unit in water. Do not operate without the air filter installed.

Drainage Options

Bucket Drainage: The unit will automatically shut off and the "Bucket Full" light will illuminate when the bucket is full. Remove, empty, and reinsert the bucket to resume.

Continuous Drainage:

Locate the drain outlet on the back of the unit.
Remove the drain plug and store it safely.
Connect a standard 5/8" inner diameter garden hose (not included). Ensure hose runs downward to a floor drain or sink.
The bucket must remain in place even when using continuous drain.

Tip: For continuous drain, place the unit on a stable surface higher than the drain point to ensure proper water flow.

Regulatory Information

This dehumidifier complies with FCC Part 15 Subpart B for Class B digital devices. It meets applicable UL and CSA safety standards. Copyright © Danby Products Inc. For support, visit www.danby.com or contact customer service at 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit does not start	No power, bucket not seated, full bucket	Ensure plugged in; check outlet; reseat empty bucket.
Reduced moisture removal	Dirty filter, low temperature, high fan speed	Clean filter; ensure room temp >41°F; use Low fan speed in cool conditions.
Bucket full light on (bucket not full)	Bucket misaligned, float stuck	Remove and reinsert bucket; check for obstructions in bucket well.
Unit cycles on/off frequently	Set humidity too low, room already dry	Increase humidity set point; use Continuous mode if needed.
Unusual noise	Loose parts, fan hitting debris	Ensure unit is level; check for objects near fan; contact service if persistent.
Water leakage	Hose not connected properly, bucket cracked	Check hose connection; inspect bucket for damage; replace if necessary.
Display not working	Power issue, control lock on	Check power cord; press and hold LOCK button for 3 seconds to unlock controls.

Reset: Unplug for 5 minutes, then restart. For persistent issues, press and hold POWER and HUMIDITY buttons for 5 seconds to reset control board.

Service: 1-800-263-2629; www.danby.com