Danby DDR070BDCWDB Dehumidifier Manual

The Danby DDR070BDCWDB is a 70-pint dehumidifier designed for residential use, featuring automatic humidity control, continuous drainage capability, a digital display with touch controls, a washable air filter, auto-restart after power interruption, and a 24-hour timer. It operates on 115V AC, 60Hz, and is ideal for medium to large rooms. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Drainage 7. Operating Modes 8. Maintenance 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Digital control panel, Water tank with full indicator and handle, Continuous drain hose port, Air filter, Casters for mobility, Power cord.

Feature	Description
Digital Display	Shows current humidity, set point, timer, and alerts
Humidity Control	Adjustable from 35% to 80% relative humidity
Continuous Drain	Port for connecting a hose (not included) for automatic water removal
Water Tank	Removable 1.5-gallon bucket with full indicator and auto-shutoff
Air Filter	Washable mesh filter to capture dust and particles
24-Hour Timer	Program on/off cycles
Auto-Restart	Resumes previous settings after a power outage
Turbo Mode	Increases fan speed for faster dehumidification
Defrost Function	Automatically activates in low temperatures to prevent coil freezing
Power Cord	6-foot cord with storage wrap

Installation

Unpack and inspect contents. Place on a level, stable surface.

Positioning: Ensure at least 12 inches of clearance on all sides for proper airflow.
Check casters: Roll unit to desired location; ensure all four casters are locked if needed.
Connect drainage (optional): Attach 5/8" inner diameter hose to drain port for continuous operation.
Plug into a dedicated 115V AC outlet.

WARNING! Do not place near heat sources or in direct sunlight. Ensure the room temperature is between 41°F and 95°F for optimal operation.

First-Time Setup

Plug in the unit; the display will illuminate.

Set humidity level: Press the HUMIDITY button and use +/- to set desired RH (default 50%).
Select mode: Press MODE to choose between Normal, Turbo, or Continuous operation.
Set timer (optional): Press TIMER to program automatic start/stop times.
Check filter: Ensure the air filter is clean and properly installed.

CAUTION! Handle the water tank carefully when full to avoid spills. Empty tank before moving the unit.

Specifications

Model: DDR070BDCWDB
Capacity: 70 pints per day (at 60% RH, 80°F)
Operating Conditions: 41°F to 95°F, up to 95% RH
Water Tank Capacity: 1.5 gallons
Power Supply: 115V AC, 60Hz, 6.5A
Air Flow: 165 CFM (Turbo mode)
Noise Level: ≤ 52 dB(A)
Dimensions (HxWxD): 23.6" x 15.4" x 11.8"
Weight: 41.9 lbs
Refrigerant: R410a

Controls and Settings

Access all functions via the digital control panel. Front Panel: POWER, MODE, HUMIDITY, TIMER, FAN SPEED, FILTER RESET.

Display Icons: Power, Tank Full, Defrost, Filter Alert, Timer, Humidity Set Point, Current Humidity.

Humidity Control: Set between 35%-80% RH. Modes: Normal (energy-saving), Turbo (high speed), Continuous (runs until tank is full or drain is active). Timer: Program up to 24 hours for on/off cycles. Fan Speed: Adjust between Low and High. Filter Reset: Press after cleaning the filter to reset the alert.

Connecting Drainage

For continuous operation, connect a hose to the drain port.

Turn off and unplug the unit.
Remove the drain cap from the back of the unit.
Insert a 5/8" inner diameter garden hose (not included) into the port.
Route the hose to a floor drain or suitable outlet, ensuring a downward slope.
Plug the unit back in; it will now drain continuously (water tank can remain in place).

Tip: Ensure the hose is not kinked and the drain path is clear to prevent water overflow.

Operating Modes

Supports multiple modes for different needs.

Normal Mode: Automatically cycles on/off to maintain set humidity level.
Turbo Mode: Fan runs at high speed for maximum moisture removal.
Continuous Mode: Runs continuously until the tank is full or power is off (ideal for very damp areas).
Timer Mode: Set to start or stop after a delay (1-24 hours).
Defrost Mode: Automatically activates when coil temperature is low; unit may pause during this cycle.

WARNING! Do not operate in temperatures below 41°F as the coil may freeze. Use in enclosed spaces only.

Maintenance

Regular maintenance ensures optimal performance and longevity.

Empty Water Tank: When full, the unit will beep and stop. Pull tank out, empty, and reinsert.
Clean Air Filter: Remove filter every 2 weeks, wash with warm water, dry completely, and reinstall.
Reset Filter Alert: After cleaning, press and hold FILTER RESET for 3 seconds.
Clean Exterior: Wipe with a damp cloth; do not use harsh chemicals.
End-of-Season Storage: Empty tank, clean filter, let unit dry, coil and store in a dry place.

Care & Cleaning

Unplug before any cleaning. Use a soft, damp cloth for the exterior. Clean the water tank with mild detergent and rinse thoroughly.

CAUTION! Do not immerse the unit in water. Never use abrasive cleaners, gasoline, or solvents.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. This product contains refrigerant R410a; dispose of according to local regulations. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit does not start	No power, full tank	Ensure plugged in; check outlet; empty water tank.
Reduced moisture removal	Dirty filter, low temps	Clean air filter; ensure room temp is above 41°F.
Water leaking	Tank not seated, hose issue	Reinsert tank firmly; check drain hose for kinks/leaks.
Loud noise	Loose parts, debris	Ensure unit is level; check for objects near fan.
Display shows "FL"	Filter needs cleaning	Clean filter and press FILTER RESET.
Frost on coils	Low temperature	Unit will auto-defrost; move to warmer area if persistent.

Reset: Unplug for 5 minutes, then plug back in to reset electronic controls.

Service: 1-800-263-2629; www.danby.com