Danby DDR070EAWDB Dehumidifier Manual

The Danby DDR070EAWDB is a 70-pint dehumidifier designed for medium to large rooms, featuring an Energy Star rating, digital humidity readout, auto-defrost function, continuous drainage option, washable filter, 24-hour timer, and quiet operation. It helps control moisture levels to improve air quality and comfort. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Placement 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Operation Modes 7. Maintenance & Cleaning 8. Drainage Options 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Digital control panel, washable air filter, removable water bucket with full-bucket alert, continuous drainage port, casters for mobility, and auto-restart function.

Feature	Description
Digital Humidity Display	Shows current room humidity and set target
70-Pint Capacity	Removes up to 70 pints per day (at 80°F, 60% RH)
Energy Star Certified	Energy efficient operation
Auto-Defrost	Prevents coil freezing in low temperatures
Continuous Drainage	Option for hose connection (not included)
Washable Filter	Captures airborne particles; reusable
24-Hour Timer	Program on/off cycles
Quiet Operation	Low noise level for residential use
Full-Bucket Alert	Light and audible signal when bucket is full
Auto-Restart	Resumes previous settings after power interruption

Installation & Placement

Unpack and inspect contents. Place on level, stable surface.

Positioning: Allow at least 12 inches clearance on all sides for airflow.
Casters: Ensure all four casters are locked if unit is on uneven surface.
Power Connection: Plug directly into a grounded 115V AC outlet.
Bucket Installation: Insert empty bucket securely until it clicks.

WARNING! Do not place near heat sources or in direct sunlight. Ensure room temperature is between 41°F and 95°F for optimal operation.

First-Time Setup

Power on dehumidifier; follow initial setup steps.

Set target humidity: Press HUMIDITY button to select desired level (35%-85%).
Select mode: Choose CONTINUOUS or AUTO mode based on needs.
Check filter: Ensure washable filter is clean and properly installed.
Test operation: Run for 10 minutes to confirm proper condensation and drainage.

CAUTION! Do not operate without the air filter installed. Handle bucket with care to avoid spills.

Specifications

Model: DDR070EAWDB
Capacity: 70 pints per day (at 80°F, 60% RH)
Power Supply: 115V, 60Hz, 7.5A
Operating Range: 41°F to 95°F
Water Bucket Capacity: 16.9 pints (2 gallons)
Noise Level: ≤ 52 dB
Dimensions (HxWxD): 23.4" x 15.4" x 11.8"
Weight: 46.3 lbs
Refrigerant: R410A
Certifications: Energy Star, ETL Listed

Controls and Settings

Access controls via digital panel on top of unit.

Control Panel: POWER, MODE (Continuous/Auto), HUMIDITY SET, FAN SPEED (High/Low), TIMER (1-24 hours), FILTER RESET indicator.

Humidity Control: Set target humidity from 35% to 85% in 5% increments. Fan Speed: HIGH for maximum moisture removal, LOW for quiet operation. Timer: Program unit to turn on/off after set hours. Filter Reset: Press and hold for 3 seconds after cleaning filter. Auto Mode: Unit cycles on/off to maintain set humidity. Continuous Mode: Runs continuously until turned off or bucket is full.

Operation Modes

Auto Mode: Unit automatically starts when humidity exceeds set point by 5% and stops when humidity is 5% below set point. Continuous Mode: Runs non-stop (bucket must be emptied regularly or continuous drainage used).

Select MODE button to toggle between AUTO and CONTINUOUS.
In AUTO mode, use HUMIDITY button to set desired level.
Use FAN SPEED to adjust airflow and noise level.
Timer can be set in either mode for scheduled operation.

Tip: For maximum efficiency, keep doors and windows closed during operation.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

Empty bucket: Remove and empty water bucket when full-bucket alert activates.
Clean filter: Remove and wash filter every 2 weeks with warm water and mild detergent.
Exterior cleaning: Wipe cabinet with soft, damp cloth; do not use harsh chemicals.
End-of-season storage: Empty bucket, clean filter, let unit dry completely, cover and store upright.

WARNING! Always unplug unit before cleaning. Never immerse unit in water.

Drainage Options

Bucket Drainage: Standard method; empty when full (indicator light and beep). Continuous Drainage: Connect 5/8" ID hose (not included) to drain port for unattended operation.

For continuous drainage: Remove bucket, attach hose to drain port, route hose to floor drain or suitable container.
Ensure hose has downward slope without kinks.
Unit will operate continuously until turned off when using hose drainage.

CAUTION! Do not lift unit while hose is attached. Ensure drainage path is clear.

Regulatory Information

ETL Listed: Meets safety standards. Energy Star: Meets energy efficiency guidelines. FCC Part 15: Class B digital device; complies with interference limits. For support, visit www.danby.com or contact 1-800-263-2629. This product contains refrigerant; dispose of according to local regulations.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not starting	Power/bucket	Check power connection; ensure bucket is properly inserted.
Low moisture removal	Filter/temperature	Clean filter; ensure room temp is within 41°F-95°F range.
Full-bucket alert not working	Float switch	Check for obstruction in bucket; ensure float moves freely.
Unusual noise	Vibration/obstruction	Ensure unit is level; check for objects touching fan or coils.
Error code displayed	Sensor/system fault	Unplug for 10 minutes, then restart; if persists, contact service.
Ice on coils	Low temperature	Auto-defrost should activate; if not, move to warmer area.

Reset: Unplug for 10 minutes to reset control system.

Service: 1-800-263-2629; www.danby.com