Danby DDR095BDPWDB Dehumidifier Manual

The Danby DDR095BDPWDB is a 95-pint dehumidifier designed for residential use, featuring a digital humidistat, auto-restart, continuous drain option, washable air filter, auto-defrost, and a 24-hour timer. It operates on 115V/60Hz power and is suitable for areas up to 4500 sq. ft. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Digital control panel, 95-pint water tank, washable filter, casters for mobility, continuous drain hose connection, and auto-defrost function.

Installation & Placement

Unpack and inspect contents. Place on a level, stable surface.

1. Clearance: Allow at least 12-18 inches of space around all sides for proper airflow.
2. Positioning: Place in the center of the room or area with high humidity (e.g., basement, laundry room).
3. Level Surface: Ensure unit is level to prevent water leakage and ensure proper operation.
4. Power Connection: Plug directly into a grounded 115V outlet. Do not use an extension cord.

WARNING! Do not place near heat sources or in direct sunlight. Ensure the area is well-ventilated.

First-Time Setup

Power on the dehumidifier; follow initial setup steps.

1. Install the filter: Ensure the washable air filter is correctly seated in its slot.
2. Set humidity level: Press the HUMIDITY button to set your desired level (start at 50%).
3. Select fan speed: Choose between HIGH or LOW fan speed for your needs.
4. Check drain hose: If using continuous drain, attach the hose securely to the drain port.
5. Run initial cycle: Allow the unit to run for 24 hours to assess performance.

CAUTION! Handle the water tank with care to avoid spills. Ensure the tank is properly inserted before operation.

Specifications

• Model: DDR095BDPWDB
• Dehumidification Capacity: 95 pints per day (at 80°F, 60% RH)
• Coverage Area: Up to 4500 sq. ft.
• Power Supply: 115V / 60Hz
• Amperage: 7.5A
• Water Tank Capacity: 16.9 pints (2 gallons)
• Operating Temperature: 41°F to 95°F (5°C to 35°C)
• Noise Level: ≤ 52 dB
• Dimensions (HxWxD): 23.4" x 15.4" x 11.8"
• Weight: 46.3 lbs
• Refrigerant: R410A

Controls and Settings

Access all functions via the digital control panel. Front Panel: POWER, HUMIDITY SET, FAN SPEED, TIMER, FILTER ALERT, FULL TANK indicator.

Remote Control (if included): POWER, HUMIDITY, FAN, TIMER, MODE.

Humidity Control: Set between 35% and 85%. Fan Speed: HIGH for maximum moisture removal, LOW for quiet operation. Timer: Program to turn ON or OFF after 1-24 hours. Mode: Continuous mode runs until tank is full or turned off. Filter Alert: Light indicates when filter needs cleaning. Control Lock: Press and hold FAN + TIMER for 3 seconds to lock/unlock panel.

Operation Modes

Normal Mode: Set desired humidity; unit cycles on/off to maintain it. Continuous Mode: Runs constantly until tank is full or manually stopped. Laundry Mode: Higher fan speed to dry clothes in the room (ensure room is enclosed).

1. Press POWER to turn on.
2. Use HUMIDITY buttons to set target level.
3. Select fan speed (HIGH/LOW).
4. For continuous operation, press and hold MODE for 3 seconds.
5. Use TIMER to schedule automatic shut-off or start-up.

Tip: For energy savings, set humidity to 50-55%. Use continuous drain for long-term operation.

Maintenance & Cleaning

Unplug unit before any maintenance.

1. Clean Air Filter: Remove monthly, rinse with warm water, let dry completely before reinstalling.
2. Empty Water Tank: When FULL light illuminates, pull tank out, empty, and reinsert securely.
3. Clean Exterior: Wipe cabinet with a soft, damp cloth. Do not use abrasive cleaners.
4. Clean Condenser Coils: Use a soft brush or vacuum attachment annually to remove dust.
5. End-of-Season Storage: Follow storage instructions in Section 10.

WARNING! Never operate without the air filter. Do not tilt or turn unit upside down.

Drainage Options

Manual Drain: Use the 16.9-pint bucket; empty when FULL light comes on. Continuous Drain: Attach a standard garden hose (not included) to the drain port for gravity drainage.

1. Locate the drain port on the back of the unit.
2. Remove the port cap.
3. Connect a 5/8" inner diameter hose (max length 16 ft).
4. Route hose to a floor drain, sink, or sump pump.
5. Ensure hose has a downward slope without kinks.

CAUTION! For continuous drain, the unit must be level and the hose must be secure to prevent leaks.

Care & Storage

When not in use for extended periods:

1. Unplug the unit.
2. Empty and dry the water tank completely.
3. Clean the air filter and let it dry.
4. Run the unit in FAN ONLY mode for 24 hours to dry internal components.
5. Coil and store the power cord in the storage compartment.
6. Cover the unit and store in a cool, dry place.

CAUTION! Do not store with water in the tank. Never store on its side or upside down.

Regulatory Information

This dehumidifier complies with FCC Part 15 Subpart B for Class B digital devices. It meets applicable UL and CSA safety standards. Copyright © Danby Products Inc. For support, visit www.danby.com or contact customer service at 1-800-263-2629.

Troubleshooting

Reset: Unplug for 5 minutes to reset the electronic controls.

Service: 1-800-263-2629; www.danby.com