Danby DHCC6020 Dehumidifier Manual

The Danby DHCC6020 is a 60-pint capacity dehumidifier designed for residential use in spaces up to 3000 sq. ft. It features an automatic humidistat, continuous drain option, auto-defrost, washable air filter, digital controls with LED display, 24-hour timer, and energy-saving modes. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Placement 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Operation Modes 7. Maintenance & Cleaning 8. Storage Instructions 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Digital control panel, removable water bucket, continuous drain hose connection, washable air filter, casters for mobility, and auto-restart function.

Feature	Description
Capacity	60 pints per day (at 80°F, 60% RH)
Coverage Area	Up to 3000 sq. ft.
Humidistat	Automatic humidity control (35%-85% range)
Water Bucket	Removable with full-bucket alert and auto-shutoff
Continuous Drain	Hose connection for unattended operation
Auto-Defrost	Prevents coil freezing in low temperatures
Air Filter	Washable mesh filter for air quality
Digital Controls	LED display with humidity readout
Timer	24-hour programmable on/off timer
Energy Saver Mode	Reduces power consumption when target humidity is reached

Installation & Placement

Unpack and inspect contents. Ensure all parts are present and undamaged.

Choose location: Place on level floor, at least 12 inches from walls and furniture for proper airflow.
Install casters: Attach four casters to base if not pre-installed.
Connect drain hose (optional): For continuous drainage, attach hose to drain outlet and route to floor drain or sink.
Plug into grounded 120V AC outlet.

WARNING! Do not use extension cords. Ensure unit is upright for at least 2 hours before first use if transported on its side.

First-Time Setup

Power on dehumidifier; follow initial setup steps.

Set humidity level: Press HUMIDITY button to set desired RH (recommended 45%-50%).
Select mode: Choose between CONTINUOUS, AUTO, or ENERGY SAVER mode.
Set timer (optional): Use TIMER button to program automatic start/stop times.
Check bucket: Ensure bucket is properly seated and empty.

CAUTION! Do not operate in temperatures below 41°F (5°C) unless auto-defrost is active.

Specifications

Model: DHCC6020
Dehumidification Capacity: 60 pints/day (at 80°F, 60% RH)
Coverage Area: Up to 3000 sq. ft.
Power Supply: 115V, 60Hz, 6.5A
Water Bucket Capacity: 2.2 gallons (8.3 liters)
Operating Temperature: 41°F to 95°F (5°C to 35°C)
Noise Level: ≤ 52 dB
Dimensions (HxWxD): 19.7" x 15.4" x 11.2"
Weight: 40.8 lbs
Refrigerant: R410A

Controls and Settings

Control Panel: POWER, MODE, HUMIDITY, FAN SPEED (HIGH/LOW), TIMER, FILTER RESET.

Display Indicators: Current humidity, set humidity, bucket full, filter clean, timer, mode icons.

Mode Selection: CONTINUOUS (runs constantly), AUTO (cycles based on humidistat), ENERGY SAVER (fan stops when compressor stops). Humidity Control: Adjust between 35% and 85% in 5% increments. Timer: Set 1-24 hours for automatic on/off. Filter Alert: LED lights when filter needs cleaning; press FILTER RESET after cleaning.

Operation Modes

Auto Mode: Unit runs until set humidity is reached, then cycles on/off automatically. Continuous Mode: Runs continuously regardless of humidity level. Energy Saver: Compressor and fan stop when target humidity is met; fan runs only when needed.

Press POWER to turn unit on.
Press MODE to cycle through AUTO, CONTINUOUS, ENERGY SAVER.
Adjust fan speed with FAN button (HIGH for maximum dehumidification, LOW for quiet operation).
Monitor current humidity on display.

Tip: Close windows and doors in the room for optimal performance.

Maintenance & Cleaning

Regular maintenance ensures efficiency and longevity.

Empty bucket: When full indicator lights, turn off unit, remove bucket, and empty water.
Clean air filter: Remove filter every 2 weeks, wash with mild detergent, dry completely before reinstalling.
Clean exterior: Wipe cabinet with soft, damp cloth. Do not use harsh chemicals.
Clean bucket: Periodically wash bucket with mild soap to prevent mold/mildew.
End-of-season cleaning: Follow storage instructions for extended non-use.

WARNING! Always unplug unit before cleaning. Never immerse in water.

Storage Instructions

For seasonal storage or extended non-use:

Unplug unit and empty water bucket completely.
Clean filter and bucket as described in maintenance section.
Coil drain hose (if attached) and store with unit.
Store upright in a cool, dry place. Cover to prevent dust accumulation.

CAUTION! Do not store unit on its side. Ensure it is completely dry before storing.

Regulatory Information

UL Listed. Meets U.S. safety standards. This product contains refrigerant R410A. For proper disposal, contact local waste management authorities. Do not puncture refrigerant circuit. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit does not start	No power, bucket full, timer set	Check outlet; empty bucket; cancel timer setting.
Reduced dehumidification	Dirty filter, low temperature, doors/windows open	Clean filter; ensure room temp >41°F; close openings.
Water leakage	Bucket not seated, drain hose loose	Reinstall bucket; check hose connection.
Loud noise	Unit not level, loose parts	Place on level surface; check for obstructions.
Display not working	Power issue	Unplug for 1 minute, then reconnect.
Fan runs but no dehumidification	Low ambient temperature, defrost cycle active	Wait for defrost cycle to complete (up to 30 mins).

Reset: Unplug unit for 5 minutes to reset electronic controls.

Service: 1-800-263-2629; www.danby.com