Danby Premier DDR35E Dehumidifier Manual

The Danby Premier DDR35E is a high-capacity dehumidifier designed for residential use, featuring electronic controls, a digital display, adjustable humidity settings, continuous drainage option, auto-restart, and a washable filter. It efficiently removes excess moisture from the air to improve comfort and protect your home from mold and mildew. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Electronic control panel, Digital display, Water tank with full indicator, Continuous drainage port, Washable air filter, Casters for mobility.

Installation

Unpack and inspect contents. Place on a level, stable surface.

1. Positioning: Place the dehumidifier in the center of the room, at least 12 inches away from walls and furniture for proper airflow.
2. Check Filter: Ensure the air filter is properly installed.
3. Drainage Option: For continuous drainage, connect a standard garden hose (not included) to the drain port and route to a floor drain or suitable outlet.
4. Power Connection: Plug the power cord into a grounded 120V AC, 60Hz outlet.

WARNING! Do not use an extension cord. Ensure the unit is on a level surface to prevent water leakage.

First-Time Setup

Plug in the unit; the digital display will illuminate.

1. Set Humidity: Press the HUMIDITY button to set your desired level (recommended 45-50% for general comfort).
2. Select Fan Speed: Choose between HIGH or LOW fan speed using the FAN button.
3. Timer Setting (Optional): Use the TIMER button to program automatic start/stop times.
4. Start Operation: Press the POWER button to begin dehumidifying.

CAUTION! Allow the unit to sit upright for at least 2 hours after moving before starting, especially if it was tilted during transport.

Specifications

• Model: DDR35E (Premier Series).
• Capacity: Up to 35 pints per day (at 80°F, 60% RH).
• Coverage Area: Up to 1500 sq. ft.
• Operating Temperature: 41°F to 95°F.
• Water Tank Capacity: 1.8 gallons.
• Power Supply: 120V AC, 60Hz.
• Power Consumption: 3.5 Amps.
• Refrigerant: R410a.
• Dimensions (HxWxD): 19.5" x 13.4" x 9.8".
• Weight: 33 lbs.

Controls and Settings

Access all functions via the electronic control panel on top of the unit.

Control Panel: POWER, HUMIDITY (+/-), FAN (HIGH/LOW), TIMER (UP/DOWN), FILTER RESET.

Humidity Setting: Adjust between 35% and 85% in 5% increments. Fan Speed: HIGH for maximum moisture removal, LOW for quiet operation. Timer: Set in 1-hour increments up to 24 hours. Filter Reset: Press and hold for 3 seconds after cleaning the filter to reset the indicator. Display: Shows current room humidity, set point, timer status, filter alert, and full tank indicator.

Operating Instructions

For manual (bucket) operation or continuous drainage.

1. Manual Operation: The unit will run until the water tank is full, then shut off automatically. The FULL indicator will light. Empty the tank by pulling it out, carrying it to a drain, and pouring out the water. Reinsert firmly.
2. Continuous Drainage: Connect a hose to the drain port. Ensure the hose runs downhill without kinks. The unit will run continuously without needing to empty a tank.
3. Auto Mode: Set your desired humidity. The unit will cycle on and off automatically to maintain that level.
4. Turbo Mode: Press FAN to select HIGH speed for faster dehumidification.

Tip: For best performance, keep doors and windows closed in the room being dehumidified.

Maintenance & Cleaning

Unplug the unit before any maintenance.

1. Cleaning the Air Filter: Remove the filter every two weeks (or more often in dusty environments). Rinse with lukewarm water and let air dry completely before reinstalling. Press and hold FILTER RESET for 3 seconds.
2. Cleaning the Exterior: Wipe the cabinet with a soft, damp cloth. Do not use abrasive cleaners or solvents.
3. Cleaning the Water Tank: Empty and rinse the tank monthly with mild detergent to prevent mold or odors. Rinse thoroughly.
4. End-of-Season Care: If storing, follow the storage instructions below.

WARNING! Never operate the unit without the air filter installed. Do not immerse the unit in water.

Storage

If not using for an extended period:

1. Unplug the unit.
2. Empty and thoroughly dry the water tank.
3. Clean the air filter and let it dry.
4. Coil the power cord and store in the compartment.
5. Cover the unit and store in a cool, dry place.

CAUTION! Store the unit upright. Do not place heavy objects on top of it.

Regulatory Information

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright © Danby Products Inc. All rights reserved. For support, visit www.danby.com or contact customer service at 1-800-263-2629.

Troubleshooting

Reset: Unplug the unit for 5 minutes to reset the electronic controls.

Service: 1-800-263-2629; www.danby.com