Danby Premiere DDR30A2GP Dehumidifier Manual

The Danby Premiere DDR30A2GP is a 30-pint capacity dehumidifier designed for residential use, featuring an Energy Star rating, digital humidity display, auto-restart function, continuous drain option, washable filter, and quiet operation. Ideal for rooms up to 1500 sq ft. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Digital control panel, 30-pint water tank, washable air filter, continuous drain hose connection, casters for mobility, and auto-defrost function.

Installation & Placement

Unpack and inspect contents. Place on level, stable surface.

1. Remove packaging materials and tape from unit.
2. Place dehumidifier on level floor with at least 12 inches clearance on all sides.
3. Ensure room temperature is between 41°F (5°C) and 95°F (35°C) for optimal operation.
4. Keep away from heat sources and direct sunlight.
5. Install casters if not pre-attached.

WARNING! Do not place in confined spaces or block air vents. Ensure proper ventilation.

First-Time Setup

Plug into grounded electrical outlet; follow initial setup steps.

1. Insert water tank securely until it clicks into place.
2. Plug power cord into 115V, 60Hz grounded outlet.
3. Press POWER button to turn on unit.
4. Set desired humidity level using UP/DOWN buttons (30%-80% RH).
5. Select fan speed (LOW/HIGH) based on room conditions.
6. For continuous drainage: Connect hose to drain port (hose not included).

CAUTION! Use dedicated outlet; avoid extension cords. Allow unit to stand upright for 24 hours if transported horizontally.

Specifications

• Model: DDR30A2GP
• Capacity: 30 pints per day (at 80°F, 60% RH)
• Coverage Area: Up to 1500 square feet
• Power Supply: 115V, 60Hz, 3.7A
• Water Tank Capacity: 1.6 gallons (6 liters)
• Operating Conditions: 41°F to 95°F (5°C to 35°C)
• Noise Level: ≤ 52 dB
• Dimensions: 15.4" W × 11.4" D × 19.9" H
• Weight: 33 lbs
• Refrigerant: R410a
• Certifications: Energy Star, ETL Listed

Controls and Settings

Digital control panel includes: POWER, HUMIDITY SET, FAN SPEED, TIMER, FILTER RESET.

Display Indicators: Current humidity, set point, full tank alert, filter clean, defrost mode.

Humidity Control: Set between 30%-80% RH in 5% increments. Fan Speed: LOW for quiet operation, HIGH for maximum moisture removal. Timer: 1-24 hours for automatic on/off. Auto-Restart: Unit resumes operation after power outage. Auto-Defrost: Activates automatically when coil temperature drops below 41°F.

Operation Modes

Normal Mode: Set desired humidity level; unit runs until target is reached. Continuous Mode: Runs continuously regardless of humidity (for very damp conditions). Laundry Mode: Higher fan speed for drying clothes. Timer Mode: Program unit to turn on/off at specific times.

1. Press POWER to turn on unit.
2. Use UP/DOWN buttons to set target humidity.
3. Press FAN button to select LOW or HIGH speed.
4. For continuous operation: Set humidity to lowest setting (30%).
5. For laundry drying: Select HIGH fan speed and place in closed room with wet laundry.

Tip: Close windows and doors for most efficient operation.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Water Tank: Empty when full or every few days. Clean with mild detergent monthly.
2. Air Filter: Clean every 2 weeks or when FILTER light illuminates.
   • Remove filter from front grille
   • Rinse under warm water
   • Allow to dry completely before reinstalling
   • Press FILTER RESET button after cleaning
3. Exterior: Wipe with damp cloth; do not use abrasive cleaners.
4. Coils: Vacuum gently every 3 months to remove dust.

WARNING! Always unplug unit before cleaning. Never immerse in water.

Drainage Options

Two drainage methods: Manual (bucket) or Continuous (hose).

Manual Drainage:

1. Unit automatically shuts off when tank is full (FULL TANK light illuminates)
2. Pull water tank straight out
3. Carry to drain location using both handles
4. Empty completely
5. Replace tank securely until click is heard

Continuous Drainage:

1. Remove drain plug from back of unit
2. Connect 5/8" ID hose (not included)
3. Route hose to floor drain or suitable location
4. Ensure hose has downward slope without kinks
5. Unit will drain continuously without needing to empty tank

Care & Storage

When not in use for extended periods:

1. Unplug unit from outlet.
2. Empty and clean water tank thoroughly.
3. Clean air filter and let dry completely.
4. Run unit in FAN ONLY mode for 30 minutes to dry internal components.
5. Coil power cord neatly and secure with twist tie.
6. Store in upright position in dry, covered area.
7. Cover unit to prevent dust accumulation.

CAUTION! Do not store with water in tank. Avoid extreme temperatures during storage.

Regulatory Information

ETL Listed: Meets safety standards. Energy Star: Exceeds federal energy efficiency guidelines. FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629. This product contains R410a refrigerant. Dispose of properly according to local regulations.

Troubleshooting

Reset: Unplug unit for 5 minutes to reset electronic controls.

Service: 1-800-263-2629; www.danby.com