Danby Premiere DDR70A1GP Dehumidifier Manual

The Danby Premiere DDR70A1GP is a high-capacity 70-pint dehumidifier designed for large rooms and basements, featuring automatic humidity control, continuous drainage option, digital display with humidity readout, 24-hour timer, washable air filter, auto-defrost function, and energy-efficient operation. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Digital control panel, Water tank with full indicator, Continuous drainage port, Washable air filter, Casters for mobility, Handle for transport.

Installation & Placement

Unpack and inspect contents. Place on level, stable surface.

1. Remove packaging materials and protective tape from unit.
2. Position unit: Place on flat surface with at least 12 inches clearance on all sides for proper airflow.
3. Check filter: Ensure air filter is properly installed before operation.
4. Choose drainage: Decide between bucket collection or continuous drainage setup.
5. Plug into dedicated 115V AC outlet.

WARNING! Do not place near heat sources or in direct sunlight. Ensure proper ventilation around unit.

First-Time Setup

Power on dehumidifier; configure initial settings.

1. Set desired humidity: Press HUMIDITY button to select target level (recommended 45-50%).
2. Select mode: Choose between Normal, Turbo, or Continuous operation.
3. Set timer: Program 24-hour timer if desired for automatic operation.
4. Check drainage: Ensure water tank is properly seated or connect hose for continuous drainage.
5. Allow unit to run for 24 hours to stabilize room humidity.

CAUTION! Handle water tank carefully when full (approximately 12 lbs). Use both hands.

Specifications

• Model: DDR70A1GP Premiere
• Capacity: 70 pints per day (at 80°F, 60% RH)
• Coverage Area: Up to 4,500 square feet
• Operating Temperature: 41°F to 95°F (5°C to 35°C)
• Humidity Control Range: 35% to 85% RH
• Water Tank Capacity: 16.9 pints (2 gallons)
• Power Requirements: 115V, 60Hz, 7.5A
• Energy Consumption: 745 Watts (max)
• Noise Level: 52 dB (normal mode)
• Dimensions: 15.4" W × 11.4" D × 24.3" H
• Weight: 46.3 lbs
• Refrigerant: R-410A

Controls and Settings

Access control panel via front display. Control Buttons: POWER, MODE, HUMIDITY, TIMER, FAN SPEED, FILTER RESET.

Display Indicators: Power, Full Tank, Filter Clean, Defrost, Timer, Target Humidity, Current Humidity.

Humidity Settings: Adjust between 35%-85% in 5% increments. Timer: Program 1-24 hours for automatic start/stop. Mode Selection: Normal (standard operation), Turbo (maximum dehumidification), Continuous (runs until tank full). Fan Speed: High/Low settings for noise control. Filter Reset: Reset indicator after cleaning filter.

Operation Modes

Normal Mode: Standard dehumidification with automatic cycling. Turbo Mode: Maximum moisture removal for high humidity conditions. Continuous Mode: Runs continuously until tank is full (bypasses humidity setting).

1. Press POWER to turn unit on.
2. Select MODE to choose between Normal, Turbo, or Continuous operation.
3. Set target humidity using HUMIDITY buttons.
4. Adjust fan speed if desired (affects noise level and air circulation).
5. Unit will automatically cycle on/off to maintain set humidity level.

Tip: Use Turbo mode initially in very damp areas, then switch to Normal mode for maintenance.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Clean air filter every 2 weeks: Remove, wash with mild detergent, dry completely, reinstall.
2. Empty water tank: When full indicator lights, turn unit off, remove tank, empty, replace securely.
3. Clean exterior: Wipe with damp cloth only; do not use chemicals or abrasives.
4. Clean water tank monthly: Use mild detergent to prevent mold/mildew buildup.
5. Check drainage hose: Ensure continuous drainage hose is clear of kinks or blockages.
6. Off-season storage: Empty tank completely, clean unit, store in dry location.

WARNING! Always unplug unit before cleaning or maintenance. Never immerse unit in water.

Drainage Options

Bucket Collection: Standard method using removable water tank. Continuous Drainage: Connect 5/8" ID garden hose to drain port.

1. For bucket collection: Ensure tank is properly seated; unit will shut off when full.
2. For continuous drainage: Place unit near floor drain or sink; attach hose to drain port; ensure downward slope for gravity flow.
3. Check hose connection: Ensure secure fit to prevent leaks.
4. Test drainage: Pour small amount of water through system to verify flow.

CAUTION! Do not lift unit with water in tank. Empty before moving.

Energy Saving Tips

Set humidity to 50% for optimal balance of comfort and efficiency. Use timer to run during peak humidity hours only. Keep doors and windows closed while unit operates. Ensure proper filter maintenance for optimal airflow. Use in temperatures above 41°F to avoid defrost cycling.

Regulatory Information

UL Listed: Meets safety standards for household use. Energy Star Certified: Exceeds federal energy efficiency standards. EPA Refrigerant Compliance: Uses R-410A, an environmentally friendly refrigerant. Copyright © Danby Products Inc. For support, visit www.danby.com or contact 1-800-263-2629.

Troubleshooting

Reset: Unplug for 10 minutes to reset electronic controls.

Service: 1-800-263-2629; www.danby.com